Results 1 to 4 of 4
  1. #1

    Join Date
    Feb 2004
    Location
    ny
    Posts
    191
    Post Thanks / Like

    SSR 2 with megs yellow pad?

    How well will SSR 2 with megs yellow pad take out medium swirls? Also what speed fdo you guys reccomend?

  2. #2
    Detailing Stare keeotee's Avatar
    Join Date
    Feb 2004
    Location
    Northeast Ohio
    Posts
    658
    Post Thanks / Like
    I think you will find it will do a good job of it. A speed of 5 to 5.5 is what I use. Work it well.
    If the wolf howls by the light of the moon in the dark of the night...

  3. #3

    Join Date
    Feb 2004
    Location
    ny
    Posts
    191
    Post Thanks / Like
    should i do one panel at a time then buff off and then repeat if neccesesary? or do the whole car then buff off then repeat if neccesesary or it doesnt matter? also after the SSR 2 should i follow with PwC with another yellow pad and then top with EX with a finishing pad or should i use a finishing pad for PwC?

  4. #4
    Detailing Stare keeotee's Avatar
    Join Date
    Feb 2004
    Location
    Northeast Ohio
    Posts
    658
    Post Thanks / Like
    Check out this terrific article:
    http://bimmer.roadfly.org/bmw/forums...1430487&page=1

    Do one section at a time and wipe off the product residue. I do one section of the hood at a time, wipe the residue off, finish with the hood and then pull it out into the direct sunlight and examine my work and the results before going further. Know what you`ve accomplished before doing the whole car with the routine and approach you are using.

    I`m just learning myself, but last weekend I used the yellow pad and SSR1 on my truck. The weather was such that I couldn`t verify my work (too overcast), so I did the whole truck like that. Turns out I really should have used SSR2 with the yellow pad. The truck was greatly improved but not as good as I wanted.

    As for following up with PwC, then EX with a finishing pad, I think the finishing pad with EX is fine, but I`m not sure about the PwC. I would think that would be fine though since you`ve already done swirl removal. As for topping PwC with EX, I`m not sure about that. And you`re paint is going to be pretty clean after the SSR2 I should think.

    Yesterday I did the wife`s car with the yellow pad and SSR2, well, I got most of it done. I then followed up with AIO by hand and then topped with UPP and finally Trade Secret. I really only used the AIO to be certain I got any SSR2 residue removed and as a good base for the UPP.

    Certainly others can and will offer advice and correct me if I`ve made a statement in error here.

    Hope this is of some help.
    If the wolf howls by the light of the moon in the dark of the night...

 

 

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Menzerna SIP on megs yellow pad followed by SF on blue, or something inbetween?
    By Guitarist302008 in forum Machine Polishing & Sanding
    Replies: 7
    Last Post: 04-10-2014, 09:16 PM
  2. Megs Maroon or Yellow
    By solekeeper in forum Car Detailing
    Replies: 9
    Last Post: 06-15-2010, 10:59 AM
  3. Natty`s Blue vs Megs Hi-Tech Yellow #26
    By mysteryan in forum Car Detailing Product Discussion
    Replies: 37
    Last Post: 01-27-2008, 03:10 AM
  4. Edge yellow vs Megs burgundy...
    By wannafbody in forum Machine Polishing & Sanding
    Replies: 2
    Last Post: 09-16-2006, 02:31 PM
  5. Cleaning yellow megs pads
    By Blazern00b in forum Machine Polishing & Sanding
    Replies: 3
    Last Post: 03-05-2005, 12:22 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •